#Starwind 19 free#

Information here to make sure it matches up with your boat. Thus, for safety and other reasons, it is a good idea to verify Because this information has come from many sources we can not guarantee its accuracy.Д®ven if this information is the same as the original factory specs, boats are sometimes modified.

#Starwind 19 free#

Information on this page is provided to you as a free service of. More importantly, the right maintenance, care, and equipment can help you to have a safer, more enjoyable time on the water. Proper maintenance and care can help your Starwind stay in good condition and have a higher value at resale. To help ensure your safety, we highly recommend sailing classes since sailing can be a challenging activity where technique and skills are important. Dacron, 3 partial battens, with a bolt rope luff, sailbag, and other features. Sailing is a great activity and can provide you and your family andДЇriends with many hours of enjoyment. If you are buying a sailboat, check the waters where you plan to sail to make sure they are not too shallow for the craft you plan to buy.) (Draft refers to the bare minimum amount of water needed to sail your vessel. The draft of this sailboat is approximately 4'6'. TheДisplacement for the boat is approximately 1350 lbs. The width (or beam) of this craft is 76 inches. None of this data has been checked by so please always check your boat before relying on this data.The 1985 Starwind 19 sailboat has a fiberglass hull and has an overall length of 18.58 feet (sometimes referred to as LOA). In addition, some boats have been modified from stock and will not match the data in these databases. There are errors as you can see as the different data bases do not always agree. The information in these data bases is a starting point. ' LP' is the shortest distance between the clew and the luff of the genoa.Дata*This data is supplied as a reference and all boat dimensions should be verified before using it in any critical application. ' JY' is the measurement from the staysail stay to the front face of the mast. ' IY' is the measurement from the staysail halyard to the deck. ' PY' and ' EY' are, respectively the luff length and foot length of the mizzen of a yawl or ketch measured in the same way as for the mainsail. ' ISP' is measured from the highest spinnaker halyard to the deck.

' JSP' is the length of the spinnaker pole or the distance from the forward end of the bowsprit (fully extended) to the front face of the mast. ' J' is the base of the foretriangle measured along the deck from the headstay pin to the front of the mast. The main deck is where the deck would be if there were no deckhouse. ' I' is measured along the front of mast from the genoa halyard to the main deck. ' E' is the foot length of the mainsail, measured along the boom from the aft face of the mast to the outermost point on the boom to which the main can be pulled or to the black band. ' P' is the luff length of the mainsail, measured along the aft face of the mast from the top of the boom to the highest point that the mainsail can be hoisted or black band. 'Square' Spinnaker Area = Max Luff x Max Girth) = 214 sq ft The 7 foot 9 inch settee and quarterberths extend well into the cabin and proves more than. Steck opted for an open funtional design. Below deck, PERFECTION's generous beam is evident. Spinnaker Area = Max Luff x Max Girth x ( 70-85%) = 150 to 182 sq ft The Starwind 223 specifications: LOA 22'3' LWL 19'4' Beam 8'6' Draft Board Up 22' Board Down 5'0' Displacement 2435 lbs. They are rules of thumb, not measurements of a this specific boat.ДЎ55% Genoa = (( J x I ) / 2) x 1.65 = 99 sq ftДЎ35% Genoa = (( J x I ) / 2) x 1.44 = 86 sq ftДЄ more accurate LP calculator is HERE Spinnaker But all things considered, these numbers are close but should not be considered exact. Also, remember that jib sail area in general is based on the forestay length, I. Sail areas depend on lots of factors, leach hollow, foot round, luff hollow etc.